Analog-Digital Converter

Publication: Syntax
Pub Details: Syntax/Syntax ZX80 v5 n11 (Volume 5, Issue 11)
Date: November 1984
Pages: 4
Product:  Analog-Digital Converter
Machines: ZX81, TS1000, TS2068
Price:    $29.95 + $4.95 P&H
From:     Byte-Back Co.
          Rt 3, Box 147
          Leesville, SC  29070
          803/532-5812

Used with your BB-1 I/O board, this converter outputs 255 at 0 V down to 0 at the full-scale input voltage and puts the data in memory. You then read it out by peeking a memory location and use the data in your program.

Housed in a plastic tube about 1 inch in diameter and 4 1/2 inches long, this converter plugs atop the BB-1 with a built-in 50-pin connector. An RCA jack at the left end accepts the DC voltage you wish to measure, and a pushbutton at the right end resets your converter at start-up. Eight DIP switches, accessible through the front, set one of five full-scale ranges: 0.25, 0.50, 2.75, 5.00, or 10.0 VDC positive only. You can’t open this device–it’s epoxied together.

SYNTAX made only simple tests of operation on two ranges–2.75 V and 5 V. In both cases the device behaved as we expected, based on the manual which comes with it. Except for the 10-Volt range, each full-scale value is individually calibrated by Byte-Back for your converter. Our 2.75-V range is actually 2.78 V; our 5 is really 5.02. Since all SYNTAX’s tests used a 1.5 V battery, we saw only the lower part of these scales.

Our converter consistently reads lower than the digital voltmeter by an amount that grows as the DC input increases. Thus, at 1.488 V input, the computer said we had 1.437 volts on the 5-V scale–about 50 millivolts low. But at 0.522 V input, the computer read 0.519 V, only 3 mV low. Similarly, the 2.75-V scale read 42 mV low at 1.492 V input and 9 mV low at 0.521 V input. Since 8-bit resolution only measures within 0.5% of full scale, these are reasonable errors.

Keep in mind that this A/D can only choose 1.471, 1.482, 1.493, or 1.504 when the input is 1.492 on a 2.75-V scale. Those are the 8-bit steps–spaced 0.0109 Volts apart. Similarly, resolution on the 5-V scale amounts to 0.0197 Volts. So you could probably get 2% accuracy with 0.5% resolution from this A/D at fixed temperature. Neither we nor Byte-Back express any opinion about temperature stability.

Since this device has parallel output, you use all input lines of your BB-1 when you connect the A/D. If you need digital inputs as well, you need another BB-1. But you can still use 8 digital outputs. In fact, you can use some to connect the converter to multiple inputs.

Well then, what use can you make of this device? Try it for applications where voltage changes are a few percent or more, but over a long interval. Or where fluctuations of your signal play a bigger role than the value. For example, a voltage in a piece of equipment with an intermittent problem.

Generally, this type of device serves best for automatic input of medium-accuracy data. For example, reading a voltage every 30 seconds for 4 hours or hourly for 7 days.

For best accuracy, store and process the bytes from the A/D. Then convert only the answer to the appropriate units.

Related reviews include the BB-1 Module (Jan.83,p.8) and the Votem A/D (Oct. & Dec.82). Votem is a 0-1 V input, serial output A/D that connects through the cassette jack.