Tired of having to type long DOS commands to select drives or load programs to run? Does RANDOMIZE USR 100:OPEN #4,”dd”:PRINT #4:CAT””,:PAUSE 0:PRINT #4:LOAD “filename.type” seem to you like a long path name instruction for a CoCo OS-9, IBM UNIX or APOLLO machine? If all you want to do is select a drive by typing in the drive number and run a program by typing in just its name, and not have to turn off the machine between programs or install a RESET switch, READ ON!
This is the second of a two part article which will give owners of the LARKEN disk system greater ease in getting around from program to program in a multi-drive system. Last time you were given a menu program to assist in locating all those great programs that you can now run. In this article you are provided with a Auxiliary Operating System (AOS) to make getting around in a multi-drive system as easy as entering the drive number you wish to go to and entering the program name you wish to run. Even if you don’t have a multi-drive system yet but have one drive and the LARKEN RAM-DISK this little program will still be of benefit to you.
Unlike other operating systems which reside in RAM and take up presious program space, this Auxiliary Operating System exits the machine when a new program is loaded in and returns when the program has finished. The features of AOS-LKDOS are as follows:
- Asks you for the drive you wish to use next.
- Automatic display of disk directory. (Catalog)
- Asks you for the program you wish to run next.
- Easily creates the AUTOSTART program on disk.
- Easily adds itself to disk.
- Easy erase routine.
- Easy Call for FORMAT and MOVE if on current drive.
- Easy call for word processor.
- Easy call for Terminal software.
- Easy call for AUTOSTART.
- Shows RLE pictures on screen.
- Prints directory out on 2040 for disk label.
Here is how the L.B1 Auxiliary-Operating System works:
With your machine turned off you hold down the J key and the <ENTER> key and turn on the machine. Instantly the DISKS.B1 program comes up on the screen and you eyeball scan the menu boards using the <NEXT> key to see where disks are in which library cases. You place the disk(s) you have selected from the library case(s) into the desired drive(s) and enter ‘Q’ for quit and <ENTER>. The DISKS.B1 program now leaves the screen and the RAM-DISK directory (catalog) or, if you don’t have a RAM-DISK, the drive 0 directory (difficult for the boviates to comprehend) appears on the screen and at the bottom of the screen the question ‘DRIVE?’.
Enter the number of the drive you wish to use next followed by <ENTER>. The directory of the disk in that drive will now appear on the screen and at the bottom of the screen the word ‘Program?’. You enter the name and extender of the program you wish to use next, hit <ENTER> and the program loads and runs.
When you are finished with the program you do one of three things, Quit from the programs menu, STOP the program and then ‘CONTINUE’, or STOP the program and enter ‘GOTO 9998’ <ENTER>. The disk directory will again appear on the screen with the word ‘DRIVE? ‘ at the bottom of the screen and you can go again as before.
The program DISKS.B1 should be on the RAM-DISK or on the disk in DRIVE 0 if you don’t have the RAM-DISK. The program L.B1 given here and AUTOSTART created by L.B1 should be on the RAM-DISK and every floppy you have. AUTOSTART can be modified to start programs other than L(arKen).B1 once it has been installed. This procedure will be discussed later.
To install the Auxiliary Operating System L.B1:
Enter the program into your machine, run it and enter the drive number that you wish to store it on. Then enter ‘S’ at the ‘Program?’ prompt, hit <ENTER> and the program L.B1 will be stored on the disk. Now enter ‘A’ at the ‘Program?’ prompt, hit <ENTER>, then ‘d’ and the program AUTOSTART will be stored on the disk.
You will now have to modify the other programs on disk to cause L.B1 to be loaded upon completion of the program. Most programs are saved on lines greater than 9990 so add line 9998 PRINT #4: LOAD “L.B1” to the program. L.B1 will then be run after each successful save. You can also type GOTO 9998 to Boot the Auxiliary Operating System. On programs that are menu driven, add a selection ‘ 0.) EXIT ‘ to the menu that directs the program to the new line 9998. On programs that end with a STOP statement you can either modify it to read ‘STOP:GOTO 9998’ so that entering CONTINUE <ENTER> after the STOP occurs will load L.B1, or change the STOP statement to read GOTO 9998.
At the ‘Program?’ prompt you can enter ‘E’ <ENTER> and you will get the ‘PRINT #4: ERASE””,’ prompt. Enter the name with the extender of the file to be erased, <ENTER> and the file will be removed from the directory. Also you can enter ‘F’ <ENTER> or ‘M’ <ENTER> and call in FORMAT.BL or MOVE.BL if they are on the current drive to perform the FORMAT, MOVE and RENAME functions.
A HELP screen is also available to show all the possible keys that will give you desired results. Just press ‘H’ at either prompt to see the HELP file. In it you will see that entering ‘W’ at the ‘Program?’ prompt will LOAD in the TASWOR.BA” word processor and ‘T’ will LOAD in the ‘MTERM.B1’ terminal software.
At the ‘Program?’ prompt you can enter ‘Z’ <ENTER> and you will get a COPY on your T/S 2040 printer of the directory screen which can be placed in the sleeve with the disk to show what all is on the disk.
To modify the AUTOSTART program, hold down the CAPS SHIFT and BREAK keys at the same time while holding down the key(s) for the AUTOSTART sequence and power up the machine. This will break the AUTOSTART program. Modify line 350 with the name and extension of the file you wish to AUTOSTART, then type GOTO 370 and ‘d’ to reinstall the modified AUTOSTART.
This program can be downloaded from the CATUG BBS using MTERM II on your Westridge 2050. Use the data parameters 8-N-1 Full-DUPLEX, buffer conversion HEX and the buffer closed and empty. Call the BBS and after connecting hit <ENTER> until you get the ‘>’ prompt. Then type: LOG SINCLAIR/GUEST
Go to the BBS download section and download L.B1 . If you wish to have this document, download L.DOC in the buffer conversion mode NONE. Remember that you are a guest on this board and please act accordingly.
If you wish a tape or disk copy of these two programs please contact me.
When you get your system disks from LarKen you will find that the TASWORD II driver modified for LKDOS doesn’t work properly. Next time we will print one for you that does work and has all the original features and more.