Part 2 AND THE AUTHOR LEARNS MORE.
I had opted to remove the MH9013 transistor and I had purchased a solder sucker at Radio Shack and I removed the transistor that I thought was good and checked it on the transistor checker and found it was NPN. Digging out my stock of spare parts (my wife thinks that I have a junk yard in the basement) I found a stock of 2N2222A transistors, a couple hundred and I selected several with adequate lengths and checked them and found one dead and pitched it and the others semed to be of the same level as the MH9013. A pin vise and a 1/32 drill followed by a drill of 0.039 diameter cleaned the solder out of the holes so the transistor leads went in easily and I carefully soldered the connections. With the chips still out I powered up and the LED power on indicator came on and no smoke. I put the chips in and with a piece of cardboard to insulate the bottom of the keyboard I powered up and got a series of beeps but nothing the screen and then silence. Subsequent handling flexed the keyboard connector cable enough that the wires parted at the circuit boards. I shelved the unit for later repair.
The second PC8300 that I ordered March 9th arrived Friday the 20th and I got lecture number XXX (not the first time obviously) from my little helpmate about the fact that I was getting far too much stuff (computers) and spending far too much time in the basement playing with said too much stuff. How can one that stands an even 60 inches be so aggressive? I saw that I was on thin ice so I waited till after supper was over and I had helped with the dishes and finished packing my lunch to take to work the next day before I dissappeared into the basement.
Yep, I got the 2nd computer and the 16K rampak however while I was getting the PC8300 out of the foam box I turned it over and got a tinny rattle and I felt something sliding inside the computer. I considered that if I sent it back I would be three weeks to a month before I get a replacement if I got one. So I carefully tilted the computer and decided that the rattle wasn’t a loose chip and was bigger that any other component that I could think of so I carefully opened the computer up and found the friction fit cover of the video modulator had came off and was rattling around. I pressed it into place and saw that the chips appeared to be firmly in their sockets and closed up the computer and carefully set it up and turned on the power.
I heard two beeps and the screen came to life in inverse video with a statement at the top left side that said READY and a flashing cursor in the bottom left corner. And each key stroke gave an audible beep that was slightly different toned for each key. I had an incomplete statement entered when I pressed the enter key and got a low pitched “growl” and the computer gave a sort of syntax error. But the manual was still in Chinese with maybe 1/4 to 1/5 in English and lots of puzzles to sort out. However it is so similiar to the T/S1000 that you could almost use the PC8300 without an instruction manual except for the twirks that are different.
When the screen came to life it was with a black screen with white characters and it came to life on channel 3 and so far I have seen no way to change that if you wanted to. Also the signal is much stronger than from the T/S1000 and you can turn the brightness and contrast controls down. The screen seems more stable. The TV cable that came with it had a different connector on the TV end and there was no TV/computer switch box included with the computer but I used the Timex switch box aand, cable since it was already in place.
I typed in some REM statements had to spell out REM and SAVE’d the program and LOADed the program back in. On SAVEing there is no 5 second blank screen it goes into the SAVE screen display and gives an OK line NO. after finishing. I typed in NEW one letter at a time and then LOAD and loaded the program back in. I have a 50 Microampere meter and a speaker across the LOAD line from the taperecorder and I can see the level of the signal and hear the signal while LOADing a program. Instead of a 5 second silence there is a shrill whistle and the whistle ends and the program begins immediately. I thought something was wrong and I aborted the LOAD but the LOAD display was still on the screen so I activiated the tape player and without the full five seconds of the whistle the program LOADed OK.
I knew from checking the signal names on the interface connector that the T/S1000 and the PC8300 were the same so I turned off the power and plugged in the T/S2040 printer and tried it. I had no trouble LLISTimg the program that I typed in and later I had the LPRINT command working except that you have to spell them out. Other accessories will possibly work if the change in the character set doesn’t confuse the computer.
I have LOADed in a couple of T/S1000 programs and one game worked or seemed to except for the character for the vehicle showed up for a letter. I haven’t tried to debug the program. I tried to load the PC8300 program on tape into the T/S1500 but it defaulted but then the T/S1500 has always been fussy about the load level. And the tape has a strong signal on it. And the 5 second whistle might confuse the computer. A friend, Mike in Muscatine, thinks that the five second whistle is a signal for the PC8300 to recognize its own program and if it doesn’t have the whistle then it will translate the program from T/S1000 to almost PC8300 Basic. I will have to experiment and try to find out.
Last night a friend stopped in and we played with the PC8300 a little and he showed me the way to run off the character set. And when he saw ink, border, paper he thought that it was a color computer and wanted to see the manual where it listed the character set. Comparing the character set as displayed by the computer with the manual the computer displays ink, paper, border while the manual states that those addresses are not used. See the character set of the PC8300 compared with the T/s1500.
Above one of the keys is the command “LINE NO.” and I hadn’t figured out yet and Gary suggested that I press shift and that key and at the bottom appeared a number and we tried it a couple of times and what it is is an automatic line numbering that increments by 10 and would help to avoid line number problems.
Reset does not work like I thought it would, in fact I don’t see a real use for it. I’ve had the computer go off into the never-never land and there was no way I could get it back without turning off the power. One possible small use is to use it to clear the bottom two lines and it does that without loosing what is in memory.
More about the manual. I did not find a Manufacturer’s name or the name of the printer and furthur I did not find any copyright notice nor a part number or book number nor an authors name. It does make you wonder and especially since the manual and the character set in the ROM are not identical. I feel that the lack of identity is a way around copy rights.
The little program given below will print out on the T/S2040 printer the character set. All key punches have been given. The complete program is as either the printer will print out or as the screen will display it after entering. You might have to enter a line like: FOR S=127 TO 255 to see it all.
9000FORS=0TO255 AFTER THE SECOND 5 PRES ENTER.
SHIFTLINE NO. (PRESS TOGETHER)LPRINTCHR$S;" "; PRESS ENTER
SHIfT LINE NO. (PRESS TOGETHER)NEXTS PRESS ENTER
9000 FOR S=0 TO 255
9010 LPRINT CHR$ S;" ";
9020 NEXT S
You will have noticed that there is no need to put in spaces when you spell out what is a single stroke entry on the T/S1000. When you enter the line the computer adds the spaces as needed and if it doesn’t it is easy to edit.
Bob Hoover did state it right: postage does cost money and when I have wrote asking for help or some such I have used a SASE. My wife is quite monetary minded and eyes the letters I write and all is fine as long as the household stamps aren’t used for my computer hobby. I will try to answer all letters; however I am into a lot of ten hour days at my work place plus a lot of Saturdays and that does eat into a lot of my time. However, after December I will be another ROC like Oscar.
Next time I will try to work from the XZ81, the T/S1000 and the T/S1500 manuals and the PC8300 manual, I will try to find the areas where the computers differ and give examples.