SYNCHRO-SETTE VOL. 2 #4 APRIL 1983
OVERCOMING CASSETTE LOADING AND SAVING PORBLEMS.
One of the most common is that an individual orders a tape from an outside source, whether it be from us or some other Software House, and can’t load it into the computer. The identical phrase is used by almost all of these people:
“This tape won’t load at all. None of the programs on wither side can be loaded into the computer. I know it’s not my tape recorder because I can save and load programs I enter myself and work just fine.”
Well, I have discovered that, in many cases, it is the tape recorder that is the culprit. “How can this be”, you say?
Simple; the RECORDING HEAD IS OUT OF ALIGNMENT. The head is saving the program off track and when it is reloaded it is reloaded off track. Programs that are saved with professional recording equipment record the pulse in proper track alignment – – – most of the time.
This problem of the head being out of alignment is a lot more common than I thought. Sometimes it can be corrected by an adjustment, as outlined in the owner’s manual. On the CTR recorders I have, there is no adjustment that I am aware of and I have to take the recorders to a service center.
If you feel your recorder might be recording off – track use another recorder (borrow a friend’s if necessary). Try loading programs you made yourself and then the commercially prepared programs.
However, if the problem cause isn’t the recorder, disconnect the EAR plug from the recorder jack and listen to the program pulses. Try to hear any of the following:
-DROPOUTS – these are sudden drops in volume that can cause the program to bomb, the result usually being the return of the (K) cursor. They may be caused by the tape becoming stretched. If there is a lack of magnetic particles in any part of the tape, dropouts can occur. Demagnetising the tape with a bulk eraser before recording on it can sometimes help. Dropouts can sometimes be overcome by increasing the volume adjustment of the recorder. A trick I have used, that sometimes works is to locate the dropout location by noting the position of the number counter. I load the tape again and when the tape approaches that position, I increase the volume on the recorder and then decrease it when that position is safely passed.
-WAVERING- This is the effect where the volume of the sound pulse pattern keeps cycling from high to low in a constant manner. At the high point the program might blow. At the low point, data might be lost to the computer. Volume adjustment sometimes overcomes this effect but in extreme cases, nothing helps except if a device, such as the Winky Board (G. Russell Electronics) is used. This problem is caused by either a bad recorder or a bad tape.
-DISTORTION- Extra noise on the tape interferes with the computer’s ability to identify the program pulses. This may be leftover strong pulses if the program was recorded over an old program. Again, de-magnetizing or a device like the Winky Board can help.
– UNEVEN PULSE RATES – This can usually be traced to a problem with the recorder’s drive mechanism. The belts may be slipping or the motor maybe binding. Cosult the recorder manual for proper lubrication and cleaning procedures, If belts receive a coating of lubricant, all sorts of problems can arise. Belts can enlarge as they get old and may have to be replaced. Sometimes they just keep falling off the drive wheels.
-EXTREMELY HIGH VOLUME- The result of this is usually the screen going blank with no cursor. This is usually easy to remedy just by turning down the volume except if there is some other kind of distortion, also.
Sometimes, the head of the recorder itself becomes magnetized or dirty. It is usually a simple procedure to clean or demagnetize the recorder head. Most venders of cassette recorders sell tape cleaning and demagnetizing devices.
**If you have trouble SAVEing programs, I might suggest:
-MAKE SURE THE PROGRAM IS NEVER SAVED AT THE BEGINNING OF THE TAPE. You have no idea how many times people have tried to save a program before advancing the tape beyond the leader. All tapes (except leaderless tapes) have a segment at the beginning and end made of a plastic material that have no magnetic particles in it. These segments are designed to affix the magnetic tape to the two spools. They cannot hold the data themselves.
– Disconnect the plug from the recorder EAR jack while recording. The recorder may pick up unwanted noise from the computer through this circuit.
– Use quality cassettes. They don’t have to be expensive and some expensive tapes as less suited for storing computer pulses.
– Run the recorder on batteries instead of AC. The AC power source into the recorder may introduce voltage spikes or hum that shows up as distortion in the recorded program pulses. Some recorders may have a problem keeping the drive motor operating at a constant RPM when on DC current so make sure the batteries are fresh.
– Find out if there is an extreme amount of noise that accompanies the program when the RAMpak is attached and a program is saved, as compared to saving a program with the RAMpak un-attached. If there is more noise, consider obtaining another RAMpak. Our experience has shown the Memotech RAMpak to be less noise – producing than most.
– In extreme cases, run the computer on batteries when saving a program. This involves building a power supply with batteries. Make sure that the proper polarity is observed. The power plug tip should be positive that comes from the battery pack and goes into the computer. IMPROPER POLARITY CAN CAUSE DAMAGE TO THE COMPUTER. If you have any doubts, ask someone who has some expertise in this area. I built such a device with NiCad rechargeable batteries inside a metal case with an input jack for the computer’s power supply which is used to charge the batteries – on/off switch, output plug on a two wire cord for the computer and DC meter to check the power status of the batteries. The whole thing cost me less than $30.00 and I bought all the parts from Radio Shack.
**If you have trouble LOADing programs:
– Disconnect the plug from the recorder MIC jack while loading.
– If the recorder has a treble/bass adjustment, the treble should be at maximum level and bass at minimum.
– If the recorder has a high/low switch it should be at high.
– The volume adjustment, if set at 75% maximum, is usually the best setting.
– Run the recorder on batteries.
I don’t suggest you try all these things at once but one at a time until whatever problem you have is overcome.