The inch-square Winky Board 2 is worth its weight in gold
The dream of every user of the T/S1000,ZX81 is to own a secret device that will virtually guarantee a good load every time, no matter what tape player is being used. Add to that an ability to let you save a program on one tape recorder and to load it using a different one. Impossible, we hear you cry! Well, the impossible is with us in the form of Bill Russell‘s Winky Board 2. He named it for its winking LED lights.

This little piece of hardware (only about an inch square) was demonstrated to us at the last meeting of the T/S division of the Boston Computer Society. Nearly every person at that meeting bought one. We brought ours back to our office to give it a “real” test.
The Winky 2 is an open board cassette/computer interface designed specifically for the T/S1000 and T/S1500 computers. It actually eliminated every difficulty we had loading and saving even the most problematic programs. If that was all it did, we would consider it worth the money. But that is just the start of the wonders this little device will perform.
The copyright laws allow you to make one back-up copy of any cassette you buy. That’s all well and good, but if the program is in machine code and you can’t break it, how can you make your back-up copy? Bring on the Winky board. It will copy any program you can load, and you don’t have to break into the program to do it. The Winky has the ability to make copies as it is loading. That is, the load and the copy are made at the same time. And the copy is usable even if the entire original is done in machine code.
Is it beginning to sound too good to be true? Well, as a little added bonus there is an earphone plug that lets you listen in on the signal while you are saving or loading. This lets you monitor verbal information on the tape before the program without having to unplug the computer from the tape machine.
The two LED monitor lights that wink at you can be used to find the ideal volume setting for any program or tape recorder to further enhance your chance for a perfect load every time. To use this mode of the Winky board, set the volume on the tape player to low. Plug in the earphone to monitor any verbal instructions on the tape. When the program signal starts coming through, turn the volume up until the first LED is very bright and the second LED is barely lit. At that point you have found the ideal volume setting for that load. Rewind the tape and load the program into the computer.
When a program is being saved, some RAM packs may add high frequency electrical interference in the form of noise to the cassette. This will make loading the program later very difficult. The Winky board has a filter built into it to cut that “noise” out when you save a program.
Poorly aligned tape recorder heads cause many load failures. Again, the Winky board comes to the rescue. Using the LED monitor lights and the earphone, you can easily adjust the heads on your tape. When the lights are at their brightest and the volume at its loudest, the heads are correctly adjusted. It is not a difficult procedure, and we were able to do it quickly by following Bill Russell’s clear instructions.
The documentation with the Winky board is straightforward, complete and easy to follow. Each of the Winky board’s uses is well described and diagrammed. The Winky board is passive (requires no power) so you really can’t hurt anything even if you do manage to hook it up incorrectly. It attaches to the computer and tape recorder jacks, thus leaving the RAM pack connector free.
Rating: ★★★★
About the Winky
USES
1. To give almost guaranteed loads.
2. To give cleaner saves.
3. To allow you to duplicate unbreakable programs.
4. To save and load simultaneously.
5. To make two saves at the same time.
6. To hear the signal while loading or saving.
FEATURES
1. No modifications to the computer or tape machine needed.
2. No power required.
3. Does not use a RAM pack connector. Simply plugs into the tape and computer jacks.
4. It is only one inch square.
AVAILABLE FROM
G. Russell Electronics
Road #1 Box 359 Center Hall, PA 16828
COST
Assembled and tested ............ $19.95 Kit ............................. $14.95 (earphone $1 extra)