Larry Kenny has come out with what in effect is his third generation disk interface system. Possibly one should say his 2nd generation, since it could be said that the first generation had two phases.
Lets review the background:
The first system was based on an EPROM DOS (which was bank-switched into the 63488 area of memory), plus several disk DOS’s. The second phase of this first system provided a cartridge DOS which was bank-switched into the ROM area of the computer (when disk functions were required), and eliminated the need for the EPROM- and disk-based DOS’s. The cartridge also provided several supplementary features not available on the intial system. This system was confined to the use of two DSDD drives, and formatted disks to a 160K capacity and maximum of 50 files.
The new system, the DSK400, subject of this review, consists of a cartridge board very similar to the original, plus a new interface board. The new interface board measures about 6 inches by 2 inches, and mounts horizontally behind the computer. A ribbon cable for the drive plugs into a connector at the right-hand end of the board. At the other end of the board are an NMI button and a 9-pin joystick connector. Possibly the unit could fit into an empty Memotech or Gladstone ZX81 64K RAMpack case. The board is equipped with a gold-plated female connector with a tinned male through-connector, for adding other peripherals. Four of the nine chips on the interface board are socketed. The quality of the board is very high.
The system can handle a variety of drives, up to a maximum of four. It is said to be capable of handling 3″, 3½”, and 5¼” (not 8″)single or double sided drives in single-, double-, or quad density. I have only tried it on a SA455-type 5¼” drive in the DSDD mode. In this mode disks can be formatted to hold just over 400K.
The sytem uses all the familiar Sinclair commands, including CAT, ERASE, LOAD, SAVE, MERGE, OPEN #, CLOSE #, FORMAT ,also GOTO and PRINT. All disk commands are prefaced with PRINT USR 100: or PRINT #4:
The system is compatible with the 2068 and the Spectrum mode. A Spectrum EPROM can be mounted on the cartridge and switched in with a short BASIC command from the 2068 mode. It has an AUTOSTART mode, by which you can boot a program into memory by holding the ENTER key operated while powering up the computer. Only one program per disk can be handled this way. I usually make this a MENU program to select the program that I want from the disk. This AUTOSTART program can be used to automatically boot the computer into the SPECTRUM mode from a cold start, and produce the menu.
With an appropriate EPROM DOS the cartridge is also suitable for use with several other disk systems, such as the AERCO, RAMEX, OLIGER; improving the performance of these sytems significantly. It can also be used with the OS-64 and LROS cartridge chips, by mounting them on the cartridge board.
A program to format disks is supplied on disk, along with a program to facilitate copying disks using two drives. The FORMAT program will format disks as either double or single sided, and to 40 or 80 track density.
Programs can be saved (and loaded) with all the command forms used with tape, as for example:: SAVE “progrm.B1”, SAVE “progrm.B1” LINE 100, SAVE “prog.C1” CODE start, length, SAVE “progrm.C1” SCREEN$, SAVE “progr.A1” DATA (), SAVE “progr.A$” DATA $().
Programs can be removed from the disk using the ERASE command. Tracks so erased become available for subsequently saved programs.
The NMI (snapshot) button means that you can capture to disk those unbreakeable programs on tape. Simply load your program, press the NMI button and the program will be transferred to disk. It captures the complete memory from address 22490 upwards, and uses 9 tracks of a disk. Loading one of these programs from disk takes just under 7 seconds. A disk can hold 8 of these programs, and have 7 tracks spare for menu, etc.
Programs such as Tasword, Timachine, Pro/file, MtermII are readily modified to run on the DSK400 system. Mscript with Jack Dohony‘s mods can be similarly adapted.
The joystick port accepts the 9-pin connector standard on joysticks, and works with those programs which are provided with the Kempston joystick option.
The DUMP.B1 and COPY2D.B1 programs supplied on disk with the system use a modified disk DOS which can be used from BASIC programs to control the drive operation. This means that disk utilities can be written in BASIC to perform a variety of tasks, similar to what has been done with the earlier LARKEN systems. Typical of this are three programs which I have modified for the DSK400. They are a RENAME program ,which will rename programs on disk; DOCTOR with which one can inspect and repair errors on disk tracks; and INDEXER which maintains a file of programs on a disk collection.
The DSK400 includes a number of Extended Basic commands. These permit the placement onscreen of up to three “windows” of any size, colour, and position; and writing to them in proportionally spaced characters. Also there is a set of 7 graphics patterns which can be called up as desired to fill areas of screen. A CIRCLE command will fill in selected areas of the screen with a selected pattern. INK and PAPER commands will instantly change paper/ink colours. POKE will poke numbers higher than 256 into two addresses automatically.
Conclusions:: A very easy-to-use system which will greatly enhance the use of the TS2068. Highly recommended.
Available from: Larken Electronics, R.R.#1, Navan, Ontario, Canada K4B 1H9 Price for interface board, cartridge board and drive connector cable: Can $145. (You will also need to purchase the disk drives and a power supply for them)