A Modem for the Timex 1000 or ZX-81

See all articles from Sinc-Link v1 n3
Author(s): Franz Hrazdira
Publication: Sinc-Link
Pub Details: Sinc-Link v1 n3 (Volume 1, Issue 3)
Date: May/June 1983
Pages: 6-7

After looking at many advertisements in various magazines, I found an offer which I was willing to explore further. Having been reassured on the phone that the modem kit would require nothing more to function satisfactorily than about (4) hours of my time to put it together, I ordered it right then. This was back in April.

When I received the package from Byte-Back, I was impressed – not so much with what I had paid after the exchange rate, duty and tax was added. as with the quality of the parts and documentation. Two separate manuals, covering the MD-1 modem and the RS-232 board in great detail, were supplied.

The BAUD RATE, which is the speed at which the RS-232 board sends and gets data, determined by (1) the frequency of the transmit and receive clock and (2) the divide rate of the INTEL 8251-A USART IC chip (Universal Synchronous/Asynchronous Receiver Transmitter), can be set to either 9600, 4800, 2400, 1200 or any of these baud rates divided by 16 or 64 – the most common being 300, which is 4800/16. The schematic makes available, in addition to the RS-232 level signals, also the TTL level signals for interface to any printer or other peripheral.

The MD-1 uses the new Motorola MC 6860 modem chip which MODulates and DEmodulates your signal so you can communicate with any other computer over the telephone. To do this, you first load and run a terminal program which comes on tape as part of the deal and takes up about 1.5K of your memory. Then, assuming everything was assembled correctly and the modem is connected to the phone, you can just dial up any of the following numbers on this list.

423-3265   ETI      between  5PM  and  9AM
366-2069   CFTR              6PM       9AM
978-6893   MEDICAL           7PM       9AM
499-7023   IBMPC             24  Hours
868-4000   DATAPAC
365-9621   COMPUSERVE
424-1895   for further details or a demo

Normally, you will be connected after a few ring tones. The other computer starts out with a 2000 Hz answer tone from its modem to which yours sends a 1000 Hz originate tone in reply. You are now ready to communicate by entering NEWLINE, and away you go…………

A new terminal program which is now available lets you send and receive all kinds of data, including program in BASIC and Machine Code, while doing an automatic syntactic sum check for error free transfers. After receiving, you can then review, print or save the data on tape for later use.

This program also has an automatic print mode which, if selected, will send the other computer a command to wait. After everything was printed, it will then ask for more data to be sent, to receive a new screen full and so on, until you change the mode.

Let me tell you also about a service you can subscribe to by phone, which will give your little computer the power you have only dreamt about until now. It is called Compuserve. For $5.00 US an hour, you can send and receive Electronic Mail from among 70,000 other subscribers in Canada and the US, chat on a multi-channel CB simulator with someone in Alaska, B.C., or California, post notices on a number of Special Interest Group (SIG) bulletin boards, play multi-user games, read about commodity futures or search a database on just about any topic.

I am offering starter kits to Compuserve for $60.00 CAN. They include a very basic manual, a three ring binder, a user I.D., a password, a subscription to the TODAY magazine, regular update bulletins and (5) five hours of free connect time to the service. The modem will cost you $198.00 CAN in kit form or $246.00 assembled and tested, including the basic software.

For more information, you can call me at the last number on the list.