From the Chairman’s Disk

Here it is November and for some of us it is the winter months that are beginning. Not to scare you people in the southern states away from this area but when I mowed the lawn for the last time in October I saw snowflakes coming down. And this month we had our official first snow of the year but it amounted to nothing more than wet streets since the ground was so warm that it all melted on touching the ground. But that weather signals a return, for a lot of people, to computing with the T/S computers.

Many of the projects that I had in mind to do when I last wrote just didn’t get done. But I did get some projects finished but in some cases not tested.

Printer Ribbon Re-Inking

First I will give the name and address of the place that has the supplies and directions of how to do it:

RAVEN SYSTEMS OF OAKLAND NJ INC.
P. 0. BOX 253
FRANKLIN LAKES NJ 07417

Send them a LSASE for the price list and instructions. They also have kits for the INKJET and BUBBLEJET plus color ink for the dot matrix printers. None are cheap and the $5.00 per order shipping is not cheap but it is a lot cheaper than buying ribbons and having them dry out prematurely.

Several years ago I ordered 4 oz (received 4 one ounce bottles) of black ink and three sets of felt pads. The felt pads are off white and 3/4 inch by 1/2 inch by 1/4 inch.

The instructions I had then said to glue with Krazy Glue a pad where the ribbon will rub against the pad near where it enters the cartridge. (The new instructions have drawings. See the enlarged copy I made.) I guess that is to give the ink time to be evenly distributed on the ribbon. So I glued up three ribbons and before testing for print head clearance I inked the pads. Well, the print head would hit the felt pad and keep on hitting the pads on turn on of the printer. So I stored the ribbons and forget the project. Then this last summer I took another look at the problem and I glued one pad to a ribbon and I checked for clearance and with an exacto knife I trimmed off the pad where the print head would hit it. Tested and on turn on the print head did its run to the left end of the carriage and did not repeatedly hit the pad trying to go further left as it did on the inked pads. And I had bought an electric screwdriver so I used it with a screwdriver blade out of another set to run the ribbon clear around the cartridge. I put a drop of white out on the edge of the ribbon for a marker and timed the time it took. With this ribbon and screwdriver it took 2 minutes and 13 seconds. I had put several drops of ink on the ribbon before hand. I tried the inking by printing out but it was not uniform. So I again added more ink and I redid the bit with the screwdriver. And since I didn’t use the computer for a few days the ink had more time to distribute properly. I originally thought that I would have to add a drop of ink each time but I have found that the ribbon prints out very dark without that drop of ink each time. If it starts to fade then I will re-ink.

Ink Cartridge with Inkfinity felt pad, cartridge, ribbon and take-up side (Epson FX, RX, MS type)
Ink Cartridge with Inkfinity felt pad, cartridge, ribbon and take-up side (Epson FX, RX, MS type)

Crooked Printnig Cure

The other problem with my printer (EPSON LX-810) is that with single sheet feed the paper guides sometimes get bumped and the printing is at an angle on the paper. And once it even did that in the middle of a sheet when the printer got a hard bump. So I muttered about that till I decided to add stops to the paper guides. I carefully measured the distance between the left guide and the end of the paper tray and then cut a piece of wood to fit there. I did the same for the right side. I added a piece of wood so that the stops would stay in place and painted them about the same color of the printer and they hold the guides in place and no more crooked printing. While I was cutting I also cut a guide for the right side for when I use a narrower paper to put in a small notebook. The big expense of that was the can of paint.

220 Volts AC Power Supply

The Z88 EPROM ERASER is made in the U. K. and thus requires 220 V AC to power it. I had a transformer that put out 16 volts AC and so I watched for one to use to reverse and get 220 V AC. I did find a 220 V AC transformer that put out IS volts AC so since it was just a few dollars I bought it. And when wired and under no load the output at the load end was 208 V AC. Well it might work and might not I didn’t try it. In prowling my favorite electronics place I saw a power supply that was in the wrong area and as I carried over to where it belonged I eyed the instruction sheet and it said 110/220 V AC input. It had no power cord and was a hefty thing to put out 5 V DC at 2A and 12 V DC at 4A. And from the double voltage input it had to have two 110 volt windings to make a 220 volt AC input transformer so if you connected one winding to 110 volts AC you would find a winding that put out 110 V AC. And thus if you connected those windings in series properly you would get 220 V AC. The price was right so I bought. There was a chart of what to connect to get what input. To use it on 110 VAC it said connect terminals I to 2 and terminals 3 to 4 and connect the input voltage to terminals I and 4. But if the input was 220 V AC to connect terminals 2 to 3 and the input voltage to terminals 1 and 5. So I connected it up with terminals 2 connected to terminal 3 and I connected power (110 V AC) to terminals I and 2. Then I tested across terminals I and 5 with an AC voltmeter when I plugged it in and there was 224 volts across terminals one and 5. But I had no case for the power supply. And also the DC amperage was halved because I used only one of the 110 volt windings to power the unit.

Huntington HamFest

On October 5th I went to the Huntington HamFest which is about an hours drive from here. I had a want list which included a color monitor (mine had died), a case for the power supply, certain chips for projects and 3.5 disks and disk cases for 3.5 disks. The hamFest was small. There were nine or ten venders outside and about 25 inside. This was not a make money deal since the venders (almost all radio hams) were more interested in visiting than selling. I found a color monitor (AMDEK Color-I) that was running and so I bought it. And I found some 1/2 height disk drives (400K) and a case that had originally held a power booster for a CB. At a quarter for the case I could not go wrong. The case was used to house the power supply. Lack of space prevented the installation of a switch or fuse but I can live with that. So one project got finished.

On October 13th I went to see Frank Davis and picked up another TOPPER for the Z88 and a modem for the Z88. It was rain both ways and that is about a 90 mile drive which took over two hours since about half of the way was on a narrow two lane road and there were a lot of bad curves and hills and no passing zones. Out of curiosity I would have driven to Mexico if the weather had not been bad since I was already in Peru. Of course these are all cities in Indiana and there is also a city Chilli but I am not sure where it is located.

CATUG Meeting

Then on the 19th of October (Sunday) I drove to Chicago to be at a meeting of CATUG which was held at Bob Swager’s house. That is a 240 mile drive for me and on the toll road it seemed that I needed a mint to pay the toll. $3.70 to the end of the I-80 toll road and then in side Chicago was $0.40 every few miles. And at Bob’s house I met several. I won’t go into names since I forgot most by now and I did not write anything done. Even if I had my handwriting is so bad that I still would be guessing. One person that showed up was Phillip Kwitkowski who is getting taller and taller. He came with his side kick another senior in high school but not the same school. Nazir Pashtoon also showed. There was some T/S talk and some hardware work (testing the Z88 modem) and lots of general talk. And since it was a good day with warmth and sunshine (it clouded over and sprinkled) there was Bob in the back yard with the charcoal grill and an old hair dryer blowing the charcoal to a hot condition and we had brats and hot-dogs. I could tell that the two boys had been there a lot since they quickly hauled out all the stuff to eat. The only excitement was some yellow jackets that tried to claim everything but Phil with a paper plate disposed of twenty or thirty of the yellow jackets. I stayed over at the Hoffman Estates Red Roof and returned the next day. And then Tuesday was when the weather went bad.

Color and the TS-2068

In a discussion with Bob I learned that if the power supply to the T/S 2068 was too low of voltage (below 15 volts dc) you lost color. I never had color with the monitor that died (except for a minute or two at turn on) and then when I got the Amdek I had color more. Before with the Magnavox monitor the color would be there for a very few minutes then it went to black and white. When I tested the power input under the load of the 2068 (I used a breakout box in the power line) I found the voltage to be around 18 volts. Then I received a letter from Abed and he gave me the location of the pot on the 2068 that controls color. But when I bought a second AmdeK Color-I monitor I wanted to test it with the computer I wanted to use it on. I found that it had color and it stayed color. WOW! So I finally this last week end, after coming home from the Ft. Wayne Ham and Computer Fest, tested all five of my working 2068’s and found a couple that gave color with no adjustment. Seems strange to have color. And, like now, when I am using the word processor I turn the color knob on the monitor to get b & w or nearly so. So I guess I have that problem fixed for the time being. This T/S 2068 is one that I ordered with the Russel Spectrum chip installed inside when I was at the Indianapolis Computerfest in May 1987. I believe that I ordered it through Knighted computers. I since had sent it to Dan Elliott to have the magnetic switch converted to a slide switch on the end of the computer.

Ft. Wayne HamFest

On November 15th and 16th there was a Ham and Computer Fest in FT. Wayne. I was there both days. On Saturday the 15th there were too many people to see the flea market stuff. And of course most of the real bargains had been sold Saturday but I did see some stuff and bought a little Sunday. I bought another Amdek Color-I monitor from the same person that I bought from at the Huntington HamFest and same price. I was looking at a 1/2 height drive (5.25) and the seller couldn’t answer my question of the density of the drive or even if it worked. “Here” he said take it with you, I will pitch it since I won’t take it home”. I bought very little other stuff. The drive turned out to be a 400K and tested out O.K.

At the HamFest I did not see but a few 5.25 disks and they were all high density. I did see some 720K 3.5 disks but no bargain for used ones at $0.25 each. If I wanted to go to MSDOS there were scads of used computers from almost free (some none working ones were free) to overpriced. Plenty of CD ROMs. I did see several Commodore, Apple and one TI computer. If I wanted to go Mac there was an early one for sale for $15.00 complete. I don’t know if it was the weather or what but attendance was down from last year but it seemed that more people were carrying bags of stuff. I visited with Frank and Carol Davis and he told me about some of the dealers that left Michigan in 7.5 inches of snow to come to the HamFest. My car got some 1/2 to 3/4 inches of snow on it while I was at the HamFest Saturday but the ground was wet and not slippery.

Z88

This is something that I did while trying to get another connector from the disk drive to the Z88. I have later heard that the same setup is used for an IBM but I am not sure at this time.

Z88 XOB 9 pin D sub male to 25 pin D sub female connector.

9-pin   25- pin
  1       13      9-pin   25-pin
  2       12        6     25
  3       11        7     24
  4       10        8     19 - 22 - 23
  5        9        9     19 - 22 - 23

TS-2068 Modem

I have a genuine TS-2050 Telecommunications MODEM by Westridge.

Of course there is no documentation and I wonder if anyone can supply a copy of the original manual for the unit. I have the software for its use but it would be nice to have a copy of the original documentation for the unit. I will pay for the copying and postage or if the manual is sent I will copy and return.

Musicola

I have a program “MUSICOLA” that is in cassette from which I did get IT to load and saved to both the LarKen and the Oliger system by way of the NMI button. I found no way with the error trapping used to break the program. I need the documentation to be able to use the program. Again I will pay for copying and the postage if it is sent to me. Or I will copy and return the manual. Has anyone ever converted this program to disk so that the saves and loads are to and from disk not cassette?

Byte Power

Once upon a time there were these monthly cassettes of programs by the Boisvert Brothers. There were some very good programs on them. Has anyone ever converted these programs to disk? It seems that if so that they should be shared.

That’s it for this issue. See you next issue. 0/0

Tags