Completion of this project requires the following:
An ACCURATE DVM, low temp. soldering iron, solder sucker, x-acto knife, 140 watt soldering gun, diagonal cutters, needle nose pliers, drill, a 7912 regulator chip, an assortment of resistors, a 9 pin male “D” connector, some 22 gauge insulated wire, and a little patience.
First plug in your ADAM power supply and test the output voltages. They should be very close to those in the diagram below left:

Next, unplug the power supply and remove the 4 screws that hold the heat sink to the chassis, and the 6 screws that hold the circuit board to the chassis. Now you can lift the circuit board with heat sink from the chassis to make the mods. Using the soldering gun, remove the red wires from the circuit board at E3 and E4. Remove the green wires from E8 and E7. Install the red wires in E8 and E7, and the green wires in E3 and E4. Next, with the soldering Iron and solder sucker, unsolder U4 (79M05). Remove the screw holding it and remove the regulator. Install the 7912 regulator at U4, fasten and solder it. Remove R21 and replace it with a 12K resistor. Install a 2K shunt resistor across R8.
Cover the transformer with a piece of cardboard. Lay the circuit board on top of the cardboard and plug in the power supply. Measure the voltages at the end of the gray cable. If they do not agree with the voltages in the diagram above right, you will have to experiment with resistors at R21 for +8.2V, or R8 for +5.2V, or R32 for +12.0V.
Do not proceed with this modification until these voltages are correct.
Reassemble the power supply using the screws you removed earlier. With a Groung lug and a screw and nut, solder and fasten the blue, violet and bare wires to the chassis. With diagonal cutters and x-acto knife, remove the two rectangular alignment pins from the power output connector. Scrape off the letters “TOP” from the cable end, as this surface will become the bottom when you plug it into the Q.L. later on.
PART II – Q.L. MODIFICATION FOR ADAM POWER SUPPLY OPTION
Open up your Q.L. and lay the keyboard assembly aside. Use a 9 pin “D” connector as a template to mark the spot for mounting the power jack for the modified ADAM power supply. The ideal location is through the back of the Q.L. case just to the left of the mother board. Center the connector with narrow side facing up. Mark the back of the case with felt tip pen. Use these marks as a guide for drilling out the mounting holes. Use the X-acto knife to cut the hole in the shape of your “D” connector. When the hole is the correct shape, mark and drill the two holes for fastening the connector.
Next, strip and tin 5 pieces of 22 gauge insulated wire, each about 5 inches long. Solder them to pins 1 through 5 of the “D” connector.
Solder wire from pin #1 to left leg of C54. (+12V)
Solder wire from pin #2 to upper leg of C56. (+8V)
Solder wire from pin #3 to BUS to the right of C56. (+5V) – Lower Leg
Solder wire from pin #4 to left leg of C58. (-12V)
Solder wire from pin #5 to right leg of C58. (GROUND)
Now mount the “D” connector using 4-40 or smaller screws and nuts. route the wires under the “D” connector and out of the way of the Q.L. expansion connector. Remove +5V regulator with heat sink from Q.L. Double check all of the wiring, hook up the modified power supply and fire it up! If you did it right, your Q.L. should initialize normally.
This modification will allow your Q.L. to run much cooler thus eliminating the crash problems associated with the inferior Q.L. power supply. If you still experience intermittent crash problems after doing this modification, then your mother board is probably defective.
The Unmodified ADAM power supplies are available from AMERICAN DESIGN COMPONENTS, and a few other surplus electronics dealers. If you have any trouble locating the parts or if you have other problems, write or call me and I will try to help you out.
DAN ELLIOTT
Phone: (314) 739-1712 evenings, Sunday through Thursday.
RT 1, BOX 117
CABOOL, MO. 65689