(21 Dec 93)
If you get a complete screen failure, but power light is on and you are using Gold Card, replace the 8301. Do NOT use the qpower switch mode regulator with Gold Card (I do not recommend the use of this without GC either!!)
Check with Miracle that you have the GC mods up to date.
Remove all upgrades, ROMs etc and see if fault still there.
RAM failures – use MINERVA. This will flag the FIRST faulty address in RAM, and the relevant chip can be replaced. In fact the QL std memory test will NOT pick up RAM errors where NUL bits are written. Minerva will eventually as the memory test write data is varied.
Check that your Sinclair is to latest build spec. (D14+ or has flying leads over IC23-XZ8302). If not then `2 will secure a circuit diagram and list of mods from me. Check and clean all mains connections – especially on QL power supply and mains plug (including fuse holder and screw terminals). Power socket on QL often has dry solder joints – especially if QL is used with case OFF! Don’t route mains cables anywhere near printer and disc drive cables.
Try using QL in different room/ house with and without any accessories, and with /without different monitor. If problem still there with and without cleaner then problem probably not mains interference.
Remove keyboard ribbon cables and clean cable ends & socket. If cable ends damaged and is not old type (non straight signal lines) cut off .5 cm from ends. If QL locks up (but an on-screen clock still runs) or few keys do not work this may be the cause. (To open QL case remove front 4 and back 4 screws. Do NOT undo the 2 screws under the microdrives).
Check 5v line (centre and LH pins of main regulator with large heat sink viewed from front of QL) Renew main 7805 regulator if voltage lower than say 4.8v. Smear base with silicon grease, and solder 10n capacitor direct to RH & centre pins (input) as viewed from front of QL. Make sure retaining screw is tight and that whole heat sink gets hot. 78S05 2A regulator can be used, but hardly seems worth it, and it makes no difference to expansions. Qpower switch mode regulator produces RF interference, and again doesn’t help expansions.
Take out all socketed ICs, external ROM etc, clean legs and sockets with spray cleaner and replace, pushing down hard. Take static precautions. Similarily, clean ROM socket and ROM cartridge edge connector(latter with a rubber on the solder tracks). This is VERY often a cause of crashing on my machines. Why on earth didn’t they use gold plated connector.
Thorn-EMI suggest replacing all ICs 18/23/24/34!! This is a bit drastic but if you can lay yours hands on a second working QL it is worth swapping ALL the socketed IC’s and then replacing one by one (take antistatic precautions).
Use higher capacity power supply (needs 9v DC and 16v AC) unless hardwired to board. Be SURE you know what you are doing.
I always switch on all equipment with one switch where possible. Some monitors (esp Microvitek) can cause troubles if leads are removed, maybe due to floating earths causing voltage difference and blowing 8301.
If using expansions, make sure connector pins are straight. Tony Price also recommends using a SMALL sliver of wood and cleaning expansion socket with contact cleaner.
Run thickish wire from 5v line (LH pin of regulator) to ram 5v rail (Thick circuit track running from just above R68 and under IC7).
SERIAL PORTS. If -12v and +12v lines OK, then problem usually lack of outgoing RS232. Try the 2x33k -12v pull up to 19/21 of 8302. Illogical I know but it DOES cure the problem very often. Similarily open network sockets (centre pin not making contact when plug removed) have been known to affect serial ports. These must be some internal effects in the 8302. Failing this, remove IC25 (1488) and replace in socket. I remove using specialist hot air gun, but Black & Decker electric paint stripper used CAREFULLY will work. Direct AWAY from plastic parts and don’t overheat. Lever off IC ONLY when solder is fully melted. Then try different combinations of 8302/1488. I find some 8302s output less than 2v to pin 2 of 1488 – should be 2.5 or so I am told.
Note on issue 6 boards the HAL should be socketed and swapped as well. The incoming data is buffered via this (in place of IC27 on issue 5 boards). YES – the official circuit diagram IS wrong! Try the ‘bombproofing’ mods listed in QL World in Nov 89.