This issues’ article will be short due to a few complications. Since writing my last article my QL broke down with the cartridge that Frank French supplied us in the cartridge port. Part of the problem was a short in the micro-drive which rendered Frank French’s cartridge useless. I was , however, able to make a 3 1/2″ working disc copy with a copy to disk utility that comes bundled with the C.S.T. disc system, so those programs are available on 3 1/2″ disc. After the untimely demise of my MDV1- drive I found that the disc drive system was functioning and continued to use it for 2 days until system initialization became unreliable with constant crashing and periodic failure to reset. I called A+ Computer Response and found that providing you call first, A+ will issue an authorization number and for $75.00 U.S. will either repair or replace your QL for you. Happy, I bundled up my QL and with a money order enclosed and I sent it off to A+ and waited. The turn around time was one month. The Timex turn around was about the same so for that I can’t complain. Although there is a problem! During the one month my QL was away I had occasion to hear a recorded conversation with Rod Gowen of RMG Enterprises regarding repair of 2068’s. In the course of the conversation QL repairs were mentioned. Rod said he uses the QL for his business computing and his needed repair at one time and was returned to A+ several times before it was returned in proper working order. He claims they do not bench check repaired units under load with additonal memory and peripherals before returning the repaired units. I sent my unit away July 9th/87. It was returned August 5th/87. I first tested it without any peripherals. The microdrive is now working again although after using the computer for 30 minutes it crashed. I was a little upset and never bothered to re-set and went to make a coffee, when I returned I found it has re-set itself. I decided to put a load on it and see what happened. I connected my CST 512K Ram expansion, my Eidersoft mouse and ice Rom, my CST disc interface and CST supplied NEC dual 3 1/2″ discdrives. The system now crashes and resets itself within short regular intervals and eventually after a few minutes of dark screen produces a vertical line pattern with flashing horizontal underscores or resets to the initialization screen. The July issue of Sinclair QL World Trouble Shooter a problem solver column by Bryan Davies has an insert regarding Delta 128K interfaces some were produced with a version 1.12 EPROM, others with a 1.14 EPROM soon developed a problem – the start-up screen would not come up reliably and eventually there was no screen picture. The QL service manual indicates this is a symptom of a defective ULA ZX8301 chip, next to the main processor. I realize that is what is happening with my unit and now I probably need a new ULA. Although I mentined this when I first returned my unit to A+. It is apparent this complaint was not seriously and thoroughly bench checked as my QL came back to me only half repaired. Also, apparently with the Delta interfaces and 1.14 EPROMS coupled with NEC drives a number of 8301’s failed according to Bryan Davies, yet when 1.12 EPROMS and Mitsubishi drives were used all was well. When I purchased my CST drives and CST interface I was informed that CST was moving from using Mitsubishi drives to the less expensive NEC drives. So here I am in the dark wondering was it the short in the micro-drive that caused a fault in the 8301 or it is a fault in the CST configuration and when I return the QL to A+ will it be properly repaired and bench tested under load before it is returned. Stay tuned, the Saga continues. In the meantime I amy buying a second QL to avoid any further down time. I also intend to fit it with the new Rom Sharp’s Inc. is supplying for $39.95 US. that reduces power draw by 20% and runs 50 degrees cooler on the heat sink. Along with the ROM expansion board that lets you plug 3 EPROMS’ in and use them simultaneously. I figure it will be 30 days at least before the QL being sent back for repair or the new system arrives. Hopefully by then the QL library will be back on track. In the meantime my address has changed, all contibutions to the library and correspondence to or for the QL Wayfarer should now be forwarded to:
TTSCU-QLL
or The Wayfarer
c/o Reginald Cottle
840 Eglinton Ave. West
Apt. 302
Toronto, Ontario
M5N 1G1
Hopefully by next issue we will have a catalog ready and a review of some contributions forthcoming along with the appropriate fee schedule. At this time the only copy facility I have facilitates transfer from micro-drive to disc drive so all contributions should be submitted on micro-drive cartridge until we have a reverse conversion utility.
KEEP THE SINC-LINK STRONG
We need your articles, programs, comments, or musings.
R. Cottle