Larry Kenny has come through with a cartridge DOS for his Disk Operating System. How does this DOS stack up against the original EPROM DOS and the disk DOS’?
Firstly, it takes a little getting used to. Not that it is really that difficult. It uses the standard TIMEX keyword commands for SAVE, LOAD, PRINT, MERGE, plus some less familiar keyword commands such as FORMAT, ERASE, and CAT. All these commands must be prefaced with the command PRINT USR 100:
It is possible to use a shorter prefacing command PRINT #4. The computer has to be set up for this abbreviated command by previously having entered an instruction PRINT USR 100: OPEN #4,”dd” . This instruction only needs to be set up once at the start of a session with the computer.
The cartridge appears to bank-switch the ROM in order to perform it’s tasks. It contains an 8K EPROM and an 8K RAM chip to do its tasks, and uses no computer memory.
Although my cartridge works properly, some members who have received the cartridge are having difficulty using it in the Spectrum mode. Simply put, it does not work. While the cause still remains obscure and is being worked on, we suspect it is related to the particular Spectrum ROM chip being used. In my case the Spectrum ROM has the markings AMI 8437 CCN 356 201 802 AUSTRIA. One ROM that the cartridge will not work with is marked NEC 8425X7 D 23128C 057. At the moment we are looking to see whether the problem is related to the speed of the chip, and the possibility of using an EPROM with the ROM data. ROM chips having the marking NEC are suspect.
The cartridge has an AUTOSTART feature. Simply put, you can save a program in such a way that by holding the ENTER key operated while switching the computer on will cause the disk drive to start automatically and load that previously specially-saved program. One of these special programs is permissable per disk. I make this special program the MENU for programs on that particular disk.
There is an NMI feature built into the cartridge. However, to make use of this feature you have to first build a special pushbutton circuit to trigger it. The instructions given for making up this button, while they may be adequate for the knowledgeable technician, I found were rather too sketchy for my level of expertise. I suggest that we shall have to have an article in the newsletter giving a more comprehensive description. Nevertheless, I have assembled the button circuit, and it does work as described. Load an unbreakeable program from tape, press the NMI button momentarily, a 5-note tune is heard, press a key (1 to 5), the disk starts up and chugs along for 22 tracks, the final two notes of the tune are heard, and the action on the screen recommences. Very impressive.
Normally the total memory is captured from address 22490 to 65535. However, if you press the “S” [illegible] instead of the key 1 to 5, the SCREEN will be saved, i.e. 6144 bytes starting at 16384.
I mentioned earlier that the instructions for the NMI button were sketchy. The same thing must be said about the documentation as a whole. It is likely that everything that one needs to know is contained in the four page manual. However, the paucity of detail makes the user strain to grasp the intent of the instructions. This is unfortunate, for it is a good system, and deserves better treatment.
One interesting aspect of the evolution of this system is the variety of DOS’ that are available to it. Although one might be inclined to think that with the new cartridge DOS the earlier DOS’ would no longer be useful, this is not the case. Quite a few utility programs have been written for the LARKEN system based on these disk DOS’. These utilities accessed various points in the DOS’ for particular functions that were useful in the utility programs. It appears that the cartridge DOS is not nearly so accessible, therefore the disk DOS’ will continue to be used in current utilities; and in future utilities that are written.
There is provision to piggyback a Spectrum EPROM onto the cartridge. Or an LROS cartridge EPROM can be installed. Instruction are supplied in the manual.
The cartridge contains several useful subroutines. One can open up to three “windows”, and direct output to them.
There is a fast DRAW routine.
And a fast FILL routine which can fill an area with any of 8 different background patterns.
There is a print driver routine in the DOS EPROM. However I have not found out how to control the printer line length yet, so I am unsure of it’s usefulness. Either I am missing the point, or some redesign is required on this feature.
Larry Kenny (LARKEN ELECTRONICS) advises that he is working up a new design disk interface board for the 2068 to be used with the cartridge DOS. Prices for the new interface board will be $50 US, and $65 US for the cartridge board, for a total of $115 US. Of course, you will then need the drive itself, plus a power supply for the drive. Good value for a super disk system. I recommend it.