This continuing section will provide info on interfacing printers with your system. Again, your tips and hints on adapting software and hardware to run with T/S systems are urgently needed.
REPEAT PRINTING WITH TASWORD II
The following program, when entered into TASWORD II basic portion of the program, will allow the user to select the number of copies to be printed and to abort printing if desired.
251 LET i=14: PRINT AT i,0;"No. of copies? (1)": GOSUB 6000: IF a$="" THEN LET a$="1"
252 LET k=VAL a$
277 OPEN #2,"p"
278 FOR i=1 TO k
279 OUT 63,127: REM Deletes the last character in the printer buffer
281 CLOSE #2: CLS: PRINT AT 19,0; "Press the q key to quit printing"
282 IF i<k THEN PRINT #0;"Press any key (except q) for next copy": PAUSE 0
283 IF PEEK 23560=113 THEN LET i=k
284 OPEN #2,"p":NEXT i
288 CLOSE #2
After entering the program, enter “RUN”, go back into BASIC and save a copy of TASWORD II.
This program appeared in “YOUR SPECTRUM” magazine.
YOUR SPECTRUM Subs
14 Rathbone Place,
London W1P 1DE
England
25 BPS for subscription
American Express and Visa cards accepted.
Excellent publication.
…….Bob Gilder L.I.S.T. GROUP
2040 PRINTER TIP
Add the missing edge to your 2040 printer. It is easy to make an effective paper cutting edge for your printer by taking the serrated metal paper cutting edge from a waxed paper box, cutting it to the width of the 2040 paper exit port and cementing it in place with epoxy cement. Allow the glue to dry for 24 hours prior to use.
Following this modification, you can restore the appearance of your unit by taking a black permanent type marker and colouring the cutter edge to match your printer.
PROGRAMS
This RE-REPRINT is from ZX Forum
Banta Software has provided an interesting program to us.
ON/OFF status of TS2040 printer
“As must be obvious, the REMark statement is a short machine code routine which must be the first line of the program. The other lines can be anywhere in the program and could be modified to give other messages. In the 1000/1500 version the inverse character in line 1 is “S”. Also the less than/greater than in the 2068 version and the less than/equal in the 1000/1500 version are each single keystroke entries.
2068 Version
1 REM FLASH CLS G THEN LN
9996 LET PRT=USR (5+PEEK 23635+256*PEEK 23636)
9997 IF PRT 16383 THEN PRINT "PRINTER OFF"
9998 IF PRT =16383 THEN PRINT "PRINTER ON"
9999 STOP
1000/1500 Version
1 REM = CLS ?SCS STAN
2 POKE 16516,71
9996 LET PRT=USR 16514
9997 IF PRT<>16383 THEN PRINT "PRINTER OFF"
9998 IF PRT =16383 THEN PRINT "PRINTER ON"
9999 STOP
[Editor’s note: the <> and <= single-keystroke operators did not print in line 9997 of the 2068 version and line 9998 of the 1000/1500 version.]
See the communications page for an AERCO/M Term patch.
FLASH! POKES FOR SPECTRUM ROM TASWORD WITH AERCO
FROM THE SUN T/S N/L OF GAINESVILLE, FL.
For those who have converted their 2068s to run with the Spectrum ROM there is good news! Joe Williamson has discovered the pokes necessary to run the Spectrum version of Tasword II with the Aerco interface.
First load the Aerco software then the Tasword II program. Get into BASIC by holding down on the ‘symbol shift key and pressing STOP. Select Basic from the menu then type in the following pokes without line numbers, pressing enter after each line.
POKE 57999,127
POKE 58004,98
POKE 58008,127
Now return to Tasword II with RUN and ENTER. Save your new version of Tasword II as offered by the same menu which got you into Basic.
TIMELINEZ
Also printed in LISTing April 1985.
Note: Type-in program listings on this website use ZMAKEBAS notation for graphics characters.