Since many of you own QLs and IBMs, or have friends who own IBMs, you may need to transfer documents between the two. There are programs to do this, but certain requirements must be met. The QL and IBM must have the same size disk drives. They also must be of the same density — at least the programs I tried from Quanta had this requirement. I could never get the two to match. Even after I bought a 360K, 5¼” drive for the QL it garbled the document. Big pieces of the story would come over fine, but the rest would either be lost or put in the wrong position.
At this time I should have purchased DiscOver or Multi DiscOver. I believed either of these would have done the job, but some doubted that they would work with my Delta Disk I/F. (I still think they would work, but the delay allowed me to find another solution.)
Bob Gilder (in the Sept/Oct, ’92 International QL Report) diagramed a serial cable that was different than the one I had made for my modem cable (which had been diagramed in QLINK’s manual). It used only six conductors, cross connecting a 25 pin, male connector to a 9 pin, male connector in the following manner:
25 Pin 9 Pin #2 <----------------> #2 TXD #3 <----------------> #3 RXD #5 <----------------> #5 CTS #6 <----------------> #9 DSR #7 <----------------> #7 SG #20 <----------------> #4 DTR
Since I worked as a data cabler (at the time) there was no trouble finding 20′ of twisted, 4-pair, scrap cable. We threw away hundreds of feet a day. Radio Shack had the connectors, so the total cost was about $4.00 for the finished cable. (I felt the hoods were unnecessary, since the cable would only be used occasionally.) I really didn’t think it would work so I didn’t want a big investment.
I already owned a null modem for the IBM so I connected that to the 25 pin connector. (This may not have been necessary if I had used the QL’s ser1_ port, instead of ser2_ — I don’t know for sure.) Before I connected the computers I exported one of my stories from a QUILL_DOC to ASCII, using XCHANGE’s EXPORT feature and saved it to disk. I then loaded QLINK into the QL and ProComm into the IBM (both are shareware programs). ProComm was then set to receive an XMODEM transfer, then, moving across the room to the QL, I began transmitting the document, using the XMODEM protocol without CRC. I was shocked when it worked the first time. (I had intended to use XMODEM CRC, which I thought would be compatible with ProComm’s XMODEM, later tests showed that this would not work.) I was definitely lucky.
I later found that by using TEXT87 PLUS4 I could save my stories as ASCII text with only Line Feeds at the end of each paragraph (XCHANGE’s ASCII option exports text with Line Feeds and Carriage Returns after each line). Then using QLINK’s FILTER utility I could change these Line Feeds (LFs) into Carriage Return/Line Feed combinations. Once transferred to the IBM these documents could automatically be reformatted in any way I wished using WordStar (since WordStar’s basic format is a LF/CR combination after each paragraph). This was an unexpected bonus.
After transferring several stories from the QL to the IBM, I decided to see how effective this whole procedure could be. Using Text87 Plus4, I copied a story to itself until the QL’s memory ran out. It turned out to be over 40,000 words (about half the size of a “historical” novel). I then Exported this document into an ASCII file and changed the LF’s into LF/CR combinations using QLINK. All the other serial transfers had been done at 1200 baud, but I decided to try this one at 96,000. It took about 10 minutes to get this document to the IBM and another 5 minutes to reformat the whole story into double column, justified text.
I don’t know why everything went so smoothly, but I’m not complaining. If anyone would like more information about the configuration of my computers, or help in building a cable, let me know.
Ron Blizzard — POB 54 — Weiser, ID 83672