C.LUCHT
WESTLAKE, OHIO
44145 3-29-’85
LIST
P.O.BOX 438
CENTERPORT N.Y.
11721–0438
GENTLEMEN,
Please send me three of your spectrum roms. Also cen you sell me or tell me where I can get a rom for my 2068.
I have an English Tasword two. Can you tell me how I can get it to work with my AERCO interface and a star S.G.10 printer.
I can’t get the printer to copy either. It will run a page but the head doesn’t print. Any suggestions will be tried.
I wouldn’t bother you with my problems if I could get around, but I’m seventy five years old and in a wheel chair, so I don’t get around much any more.
I’m enclosing a check for $45. for the spectrum roms.
Do any of your members have an English spectrum that I could buy and convert to 110 volts.
Of course I’d have to buy an English interface to run my STAR printer then, but that would solve my problem. Do you think that a TIMEX 1000 would run both star printer and Tasword 2? With the AERCO interface of course.
Yours truly,
Clarence Lucht
See the “Printout” Section. Thanks again to SUM.
How “letters” work – A Bootstrap
We receive dozens of requests for information each month. Some are general in nature, but most ask us specific questions about hardware, software, and compatability.
Since we don’t (and can’t) have all the different types of HW & SW available, your editorial staff simply can’t answer all the questions raised. We try, e.g., by sending pages from back issues of LISTing or referring the questions to another source of information, but we need your help.
If you see a question in the letters section, and you know the answer, please send the answer to LISTing and/or the individual. If you send it to us, we’ll publish it and pass it on.
Oh yes, we don’t print members street addresses unless told specifically to do so.
Richard C’s request is typical. I don’t have a TASMAN Interface and thus, don’t know how the software for the interface is made available to the system.
Assuming that the software printer drives reside in RAM, here’s a theoretical Solution:
POKE 64716,201: POKE 64719,201
201 is C9(HEX) or Return, so nothing will happen. To reactivate the TASMAN interface though you’d have to POKE back the original codes stored at those memory locations, so peek them first – write the values down. This could all be done from BASIC.
April 18, 1985
From the desk of:
PAUL J. DONNELLY
To: Richard C.
I can only help, right now, with question #2.
Use the system variables to find that line # and change it.
Use a header reader to find the length of the program. Next write a short routine like this:
XXXX FOR I = NEAREND TO NEAREND+50:
PRINT I;" ";PEEK I: NEXTI;STOP
Where XXXX is an unused line # NEAREND is some arbitrary address near the end of the program. E.g., if the program is 10,000 bytes long. Near end could be 33,500 or so.
GOTO XXXX and look at the Peek’s, you should be able to identify the BASIC lines from the description of how BASIC lines are set up in the manual and the character codes.
When you reach the offending line, you’ll probably find an illegal character. Poke in a legal value and all should be O.K.
Dear L.I.S.T.
Thank you so much for responding to my inquiry letter I enjoyed the sample issue (Feb 85) very much. I’m enclosing a check for you and I hope to correspond with you as well. I haven’t found a single person in the Brooklyn area who uses Timex Sinclair machines. So all of my information about these computers has to come from Books, magazines and news letters. I purchased a Timex/Sinclair 1000 about 1½ years ago and shortly afterwards bought a Timex/Sinclair 2068. My progress in BASIC has reached a point where I am beggining to assimilate the vocabulary of Z-80 machine code
Along with my check for membership, is a listing of two short routines that I have written. The use of the Dim Statement to store plot values could possibly be very usefull in other applications. The first routine uses a nested loop in conjunction with the draw command. The second routine uses a stepped variable and a loop to manipulate the draw command.
If you want, I can give you a more explicit breakdown of these routines. Anyway I hope you can take a little time to enter them on a 2068 and take a look.
Again Many thanks,
Mr. Patrick Fagan
Patrick Fagan
BROOKLYN, N.Y. 11230
PATRICK
Please do-sounds like an interesting article.
P.D.
pleasanTrees PROGRAMMING
P.O. Box 2034 Mesa, AZ 85204
March 23, 1985
Dear Paul,
Where do I begin? I have so much I want to vent.
Perhaps we’ll start with L.I.S.T.’s copy shop… Paul, the March issue was surely brimming with great stuff as always, but nearly half was indecipherable. Let’s give the copy place the deep six and find one that can do the job!
A comment on page four says Time Designs Magazines first issue was a lightweight effort. That may in fact be true, I never saw issue number one. I did just receive their third issue and its pretty darned full of good 2068 drive info. Better check it out.
Now to the A & J Micro Drive model 2000 review. The perspective sketch you included was of my own creation. I don’t mind at all you using it. It did take me hours to draw, though, just a word or two on its origin would have been nice. As for the letters on the model 2000, they echo many remarks I have heard: it is a simple device which is simple to use. It is backed by good people. Annette & Jim Howell (A & J) are to be commended on bringing to market an affordable alternative to the cassette recorder.
As for Kurt H’s letter regarding the model 2000: it was pretty sour. He not only complained about the drive but about his 2068 as well. Let’s face it, his PC has changed him. But then none of us could trade our Mercedez back for a Tercel and feel any happier. ‘Guess he’s just glad he didn’t buy the PC jr!
Best regards,
Paul Bingham
OUCH!
Paul is right about Time Design’s improvement. We thank him for the sketch. I chose it as the best and we’re not surprised that it was his. Paul’s criticisms are well intended and well taken. You might want to visit a Mercedes repair shop and check out the prices though. The faintness you see in this copy, was in the original.
MEMO FROM THE DESK OF:
RICHARD. J. CUNNINGHAM
DATE: APRIL 6, 1985
DEAR PAUL,
MANY THANKS FOR THE BACK ISSUES OF LIST. I NEVER GOT THE APRIL ISSUE HOWEVER. DID YOU SEND IT? SENT MY CHECK TO YOU ON MARCH 23.
I MENTIONED IN MY LETTER OF MARCH 23 THE PROBLEMS WITH MY A&J MICRODRIVE. WELL I NOW HAVE TWO DRIVES. THEY RETURNED THE ORIGINAL WHICH WORKS FINE AND THEY SENT THE “NEW NEW” DRIVE. THE DRIVES TAKE DIFFERENT WAFERS.
PRESENTLY I AM TRANSFERING ALL MY TAPE CASETTES TO WAFER AND AM ALMOST DONE. IT’S EASY. LOAD FROM THE RECORDER AND SAVE TO THE MICRO. TASWORD 2 HAS ADOPTED PERFECTLY. I HAVE BOTH THE 2040 PRINTER AND THE OLIVETTI PRINTER HOOKED UP TOGETHER AND CAN SELECT EITHER ONE.
I HAVE A FEW QUESTIONS MAYBE SOMEONE CAN ANSWER.
1-IS THERE ANY WAY I CAN DEACTIVATE THE TASMAN INTERFACE (RESIDES AT 64716,652. RANDOMIZE 64719 TO ACTIVATE PRINT: RANDOMISE USR 64716 FOR SCREEN COPY). IF I COULD DEACTIVATE I COULD SWITCH BETWEEN PRINTERS WITH NO PROBLEM AND ALSO LIST WITHOUT TASMAN PICKING UP THE GRAPHICS CODE INSTRUCTIONS.
2-I AM TRYING TO CONVERT THE TIMEX GOLF CASSETTE TO WAFER. IT IS WRITE PROTECTED AND THE LAST PROGRAM LINE HAS NO NUMBER. IT READS( 0383 RESET COPYRIGHT R&R ). WHEN I CALL THIS LINE DOWN TO EDIT IT CAN ONLY BE ERASED NOT CHANGED AND IT CANNOT BE REINSERTED IN PROGRAM. ANY SAVE ATTEMPT GIVES AN ERROR CODE FOR THAT LINE. ANY IDEAS??
3-HOW CAN I RESERVE SPACE FOR A SPECIFIED NUMBER OF BYTES BY USING A DUMMY PROGRAM. I WANT TO RESERVE SPACE ON THE A&J WAFERS FOR PROGRAMS THAT EXPAND SUCH AS VUFILE WHICH INCREASES IN SIZE AS FILE IS INCREASED. OTHERWISE THE ENTRIES WILL EVENTUALLY OVERWRITE THE NEXT PROGRAM ON THE WAFER. I HAVE ADOPTED VUFILE CASETTE TO THE WAFER.
IF YOU WANT MY EVALUATION OF THE A&J MICRO LET ME KNOW.
Richard
Kurt E. Hildebrant
Huber Heights, Ohio 45424
April 8, 1985
Dear Paul,
Thanks much for the Spectrum disassembly. I was really stuck on some 2068-to-Spectrum compatibility problems, but the book answered all of my questions. Please let me know how much the postage cost so that I can reimburse you. Thanks to Nazir, also, for the book !
The terminal program is coming along very well. I finally got John Oliger‘s Centronic printer interface. This is John’s finest product yet. It is a tiny ( about 2″x4″ ) board that plugs into his expansion motherboard and connects to any parallel printer via a ribbon cable. The instructions contain complete source listings for LPRINT/LLIST software and several screen dump routines. The software is also available on tape for a mere $6. This printer interface can be had for about $50 complete in kit form. With Epson RX-80 printers going for $199 now, there is no excuse for using your 2040 printer anymore ! Needless to say, I plan to support this interface in my programs.
I recently spoke to Ray Kingsley about the Oliger-Kingsley disk interface. Ray has the hardware running currently and has written most of the low-level support routines. He sees no obstacles to a CP/M operating system for the 2068. Of course, the DOS will make Ray’s HOT-Z ( already the definitive 2068 development system ) even more powerful. All you 2068 HOT-Z fanatics out there might write Ray via SINWARE and encourage his marvelous but under-paid efforts !
March 25, 1985
West Covina, Ca. 91790
USA
SMT
Greens Norton
Towchester, Northants, NN12 8BR
England
Gentlemen:
I have reviewed your offer in the March “Sinclair User” for the ROTRONICS Wafadrive for the Spectrum. As I am using the American version of the Spectrum, the Timex Sinclair 2068, I am enclosing my order. (Our ham radio Sinclair net has already verified that the WAFADRIVE works on the 2068 when a Spectrum emulator ROM is is in the cartridge dock and the Z-Link interface adaptor is used.)
As the non VAT price is 99.95 pounds I am enclosing 99.95 X $1.20 or $120 plus $15 for airmail postage or $135. The Rotronics is especially welcomed as it uses the Entrepro system “stringy-floppy” wafer from Sunnyvale, Ca. that are available here. This is its main advantage for the American market as the Spectrum interface/drives are not using an available wafer except from Sinclair.
This letter is typed on the TS-2068 and printed on a Brother EP-44 dot matrix using the Tasman RS-232 Interface and Tasword II.
Sincerely yours,
Bob Howard
JAMES E. INACKER
CHERRY HILL, NJ 08003
15 Apr 85
L.I.S.T.
c/o Paul Donnelly
10 Idle Day Drive
Centerport, NY 11721
Dear, Timex Supporter
I am the proud owner of a Timex TS-2068 and a Timex TS-1000. My computing interests lie in the area of hardware expansion and experimentation.
I have just read a very favorable review of your publication in SyncWare News Vol. 1 (recompiled).
Therefore, I would appreciate your adding my name to your subscription list.
I have enclosed a check for $12.00 (1 year). Please advise if additional funds are necessary.
Thank you.
Sincerely,
James E. Inacker
Sinclair Research Limited
50 Staniford Street · Boston · MA 02114
Telephone 617-742 4826
February 25, 1985
Mr. Paul W. Chomitz
RGC Travel Agency Inc.
New York, NY 10002
Dear Mr. Chomitz:
Thank you for your recent letter regarding the Sinclair QL. Following are responses to your particular inquiries.
1. We do not yet have FCC certification to sell either the QL or its power supply. We expect to be shipping product in May and if you re-contact us then we will be happy to sell you a power supply unit.
2. A US television will not work as display for a UK QL because of the difference in television standards (NTSC here vs. PAL there). You can, however, use any RGB color monitor with a QL. I am enclosing information on the necessary monitor interface. We will be selling monitor cables with the QL connection. We also plan to offer a QL color monitor for sale in the US concurrent with or shortly after, QL launch.
3. All expansion systems, software and applicable peripherals that are possible to be brought in and sold in the US will be imported.
4. Any domestic serial printer will work with the QL using an RS232 connector.
5. I am enclosing a product brochure, although I suspect you are looking for more technical material. QL reviews will begin appearing in the early summer. Creative Computing reviewed the QL in a late 1984 issue. Sinclair owners who enroll in the QLUB will receive bi-monthly newsletters with updated product information. There are a number of UK magazines devoted to the QL.
The problems that you are facing are the downside of having acquired a machine before it is available on the US market. However, upon launch you will see full support services for QL owners in the US.
Yours sincerely,
Mary E. Reinman
US Marketing Manager
MER:lm
Enc.
Ian F. Robertson
[address omitted]
Islington, Ontario
Canada
Paul Donnelly
L.I.S.T. Users Group
P.O. Box 438
CENTERPORT
N.Y. 11721 – 0438
U.S.A.
March 23, 1985
Dear Sir:
Enclosed please find $15.00 (U.S.) to subscribe to your TS newsletter. If this is not enough money for a one year subscription then please include a request for additional funds with my first copy.
If it is possible to start my subscription with the January 85 issue I would appreciate it.
My TS system consists of (11) TS1000/ZX81’s, (1) TS1500, (2) TS2068’s (with Spectrum ROMs) , (1) TS2050 Modem, (1) TS2040 Printer, (1) 80 column printer and assorted printer interfaces, eprom burning equipment (TS1000 & TS2068), assorted memories, assorted TS1000 Roms, assorted keyboards for the TS1000 and quite possibly the BEST TS Software and Book Library in Canada.
Looking forward to receiving your Newsletter. I remain
Yours truly,
Ian F. Robertson
[address omitted]
Starkville, MS 39759
March 19, 1985
Dear Mr. Donnelly,
I appreciate your input. The AERCO interface won’t be available for at least another month. Before I order, I am going to try to use software to interface. You mentioned FIRST LOADER from Syntax in Feb ’84 but I didn’t know which magazine you referenced. Also, I have not been able to locate your Syncware news article. We just don’t seem to have many of the Timex related publications here. I am enclosing $3.00, if you don’t mind sending me a copy, to cover copy cost, mailing, etc. Power Projects by Jim Stephen[illegible] is an excellent book & I think I will be able to use the material in it. I also found a DC to AC converter to allow the use of a printer in some cases. Our goals of the project were (1) to obtain digitized points (instead of an analog graph) and (2) to directly input the data into a data file on IBM. Both of these goals would decrease the cost in terms of labor and instrumentation and increase precision. I’ll send you a copy of my final report in May. I would also like to request your permission to use your LED output article, with proper reference, if needed. Thank you for your cooperation. If I don’t cover your charges, let me know.
Sincerely,
Joe Walker
Jess Peeler
Apdo 41 Pavas, San Jose 1200
Costa Rica, America Central
12 March 1985
LIST Group
POBx 438
Centerport, N.Y. 11721
Dear Listers:
Enclosed is another squib on the TS-1000.
Will you pose to the members – or post on your bulletin board the following information requests, please? All relate to ZX-81/TS-1000.
(a) Commercial tapes – Who sells a Contract Bridge program and who sells an Electronic Filter Design program/ and if they have gone out of business, would someone with same be willing to sell me a copy?
(b) Can someone make me a copy of Part 2 of Ian Logan‘s “Understanding Floating Point Arithmetic”, located in either Mar/Apr or May/June SYNC of 1982?
(c) Does anyone have technical info on the Westridge MODEM? I would like to obtain a MODEM, but do not like being limited to the 300 Baud that the Westridge runs at. What I need to know is if the control interfacing is done by hardware or software (And, if hardware – I need schematic diagram/ if Software – I would dearly love a copy).
Sincerely yours,
Jess Peeler